Horiba LAQUAtwin Nitrate Ion (NO3-) Tester for soil in carrying case with 5 Pipettes, 3 bottles (100 mL), 2 sampling spoons, tweezers, sampling sheet B, 2 Sampling sheet holders

HORIBA Nitrate Replacement Sensor (S040) for Pocket Testers NO3-11, NO3-11C and NO3-11SThe HORIBA LAQUAtwin Pocket Tester series allows water quality parameters to be measured quickly and accurately on site. To ensure that these measurements are reliable and accurate, it is very important to check the sensors regularly and replace them with replacement sensors if necessary. These replacement sensors have been specially developed for the HORIBA LAQUAtwin series and offer a wide range of variants for different measurements: pH value, conductivity, salinity, redox (ORP) and ion-selective sensors for sodium, potassium, nitrate, calcium and fluoride. Each of these sensors has been designed with the aim of maximising user-friendliness and accuracy, for which HORIBA is known worldwide in the field of water quality testing. The advantages of HORIBA replacement sensors are: Easy replacement: It is easy to replace the sensors, allowing measurements to be resumed quickly. Highest accuracy: The replacement sensors ensure that the measurement results are precise and reliable.Wide range of measurements: Different types of sensors are available for different water quality parameters.Durability: The sensors are designed to have a long service life even under challenging conditions. Instructions for replacing the sensor: To ensure that your HORIBA LAQUAtwin Pocket Tester is durable and accurate, please follow these steps when replacing the sensor:Remove the sensor Switch off the measuring device. Lift the tip of the sensor. Then slide the sensor slightly away from the measuring device. Remove the sensor completely from the measuring device (by pulling).Attaching the sensor  Switch off the measuring device. Make sure that the water-repellent seal is clean and undamaged. Press the sensor onto the measuring device so that hook ‘A’ on the back of the device fits into hole ‘a’ on the tongue of the sensor.Make sure that the waterproof seal is not twisted. Important:To put the measuring device back into operation for correct measurement, follow the steps in the operating instructions for the corresponding tester after replacement. (Our products include such instructions. In most cases, calibration and, if necessary, conditioning are required.)  Question: How can I check if my sensor is worn out?  Answer: By checking the condition of the sensor as follows:  Perform a 2-point calibration to check the sensor condition. If a calibration error occurs, this suggests that the sensor is deteriorating. The sensor should therefore be replaced.  Regular checks and timely replacement of sensors ensure the high quality and reliability of your water quality measurements using the HORIBA LAQUAtwin Pocket Testers.  Manufacturer item number: 3200459870

To accurately calibrate and maintain the HORIBA LAQUAtwin Pocket Testers, HORIBA provides a special selection of buffer, calibration and standard solutions. A convenient pack size of 6 x 14 ml of these solutions meets the requirements of the pocket testers as only a few drops are needed for calibration. This specific pack size helps to reduce waste and optimize efficiency during regular calibrations. The solutions available cover a variety of measurement ranges, allowing users to select the appropriate solution to suit their individual analysis or measurement needs: - pH buffer solutions: Solutions with pH values of 4.01 or 7.00 are available to calibrate the pH measurement. With these buffers it is possible to precisely regulate and control the pH measurement function of the LAQUAtwin Pocket Tester.- Conductivity standard solutions: 1413 μS/cm standard solutions ensure that the conductivity measurement of your devices is carried out precisely.- NaCl standard solutions: 0.5% or 5.0% NaCl solutions are available for the calibration of salinity measurement.- Ion standard solutions: HORIBA provides standard solutions to calibrate ion selective measurements. HORIBA provides standard solutions for sodium, potassium, nitrate and calcium, available in different concentrations: from low (e.g. 150 ppm) to high concentrations (e.g. 5000 ppm).- Fluoride ion standard solutions: For the calibration of fluoride measurements, HORIBA offers standard solutions with concentrations of 1 ppm and 10 ppm.- TISAB solution: A special solution for use with fluoride ion standard solutions to adjust the ionic strength of the sample for precise fluoride measurements.- ORP standard solution: For the calibration of redox measurements (ORP), HORIBA offers a solution with a redox potential of 225 mV. With these special solutions, the HORIBA LAQUAtwin pocket testers always provide accurate and reliable measurement results. The integrity of their measurement data and the lifetime of their devices can be ensured by regular calibration with these specifically formulated solutions. It is of great importance to select the appropriate calibration solution and standard solution to maintain the accuracy of measurements and ensure the reliability of water quality measurements in various applications. Manufacturer Part No. 3200053535

To accurately calibrate and maintain the HORIBA LAQUAtwin Pocket Testers, HORIBA provides a special selection of buffer, calibration and standard solutions. A convenient pack size of 6 x 14 ml of these solutions meets the requirements of the pocket testers as only a few drops are needed for calibration. This specific pack size helps to reduce waste and optimize efficiency during regular calibrations. The solutions available cover a variety of measurement ranges, allowing users to select the appropriate solution to suit their individual analysis or measurement needs: - pH buffer solutions: Solutions with pH values of 4.01 or 7.00 are available to calibrate the pH measurement. With these buffers it is possible to precisely regulate and control the pH measurement function of the LAQUAtwin Pocket Tester.- Conductivity standard solutions: 1413 μS/cm standard solutions ensure that the conductivity measurement of your devices is carried out precisely.- NaCl standard solutions: 0.5% or 5.0% NaCl solutions are available for the calibration of salinity measurement.- Ion standard solutions: HORIBA provides standard solutions to calibrate ion selective measurements. HORIBA provides standard solutions for sodium, potassium, nitrate and calcium, available in different concentrations: from low (e.g. 150 ppm) to high concentrations (e.g. 5000 ppm).- Fluoride ion standard solutions: For the calibration of fluoride measurements, HORIBA offers standard solutions with concentrations of 1 ppm and 10 ppm.- TISAB solution: A special solution for use with fluoride ion standard solutions to adjust the ionic strength of the sample for precise fluoride measurements.- ORP standard solution: For the calibration of redox measurements (ORP), HORIBA offers a solution with a redox potential of 225 mV. With these special solutions, the HORIBA LAQUAtwin pocket testers always provide accurate and reliable measurement results. The integrity of their measurement data and the lifetime of their devices can be ensured by regular calibration with these specifically formulated solutions. It is of great importance to select the appropriate calibration solution and standard solution to maintain the accuracy of measurements and ensure the reliability of water quality measurements in various applications. Manufacturer Part No. 3200053514

Precise Potassium Ion Measurement on the Go – Mobile, Reliable, and Easy Precise potassium ion measurement with 2-point calibration and integrated temperature display The Horiba K-11 Potassium Pocket Tester was designed to determine potassium in a wide variety of samples with high precision. Thanks to the ion-selective electrode and the digital LCD screen with backlight, the tester is perfect for mobile water quality and environmental analyses. The minimal sample volume of only 0.3 ml (0.05 ml with sampling sheet) ensures reliable results even with small sample sizes. With its 2-point calibration and automatic standard recognition, the device can be flexibly adapted to different measurement conditions. The IP67 rating for dust and water protection, along with a long battery life of up to approximately 400 hours, makes the tester highly reliable for mobile use. Technical Features for Reproducible Potassium Measurements The potassium tester covers a wide measurement range from 4 to 9,900 ppm (mg/L) and additionally displays temperatures up to 50 °C with a resolution of 0.1 °C. The integrated temperature compensation ensures stable results even under changing environmental conditions. Automatic standard recognition, adjustable calibration values, and multiplication compensation guarantee high reproducibility across different sample types. This makes the K-11 suitable for both routine and demanding analytical tasks. Why Potassium Measurement Is Important – Ideal with the Horiba K-11 Hand Tester Potassium is an essential parameter in water, environmental, agricultural, and food analysis. In water bodies, potassium content affects water quality, in soils it is a key nutrient for healthy plant growth, and in food it plays an important role for nutrition and labeling requirements. A mobile potassium hand tester enables rapid on-site analysis without time-consuming laboratory testing. Changes can be detected immediately, and decisions can be made right away. The Horiba K-11 combines this flexibility with high measurement accuracy and ease of use – ideal for fieldwork, routine checks, and scientific studies. Where Can It Be Used? Environmental Monitoring: The K-11 is a fast and precise measurement tool for environmental technicians and scientists monitoring potassium concentrations in water bodies to ensure water quality and identify contamination sources. Agriculture: The K-11 allows farmers and agronomists to measure potassium in soil. This is crucial for fertilizer application and improving plant growth. Easy evaluation of soil extracts enables precise nutrient requirement determination. Food Industry: The tester is used by quality assurance personnel to check potassium content in beverages and food. These measurements are important for product development, health assessments, and compliance with nutritional labeling requirements. Teaching, Research, and Development: By deepening the understanding of potassium’s role in biological and chemical processes, the K-11 serves researchers and educators as a useful tool for experimental studies and educational purposes.

Horiba LAQUAtwin Fluoride Ion Tester for Mobile Water Analysis Mobile fluoride hand tester with ion-selective electrode for fast and reliable on-site measurements The Horiba LAQUAtwin Fluoride Ion Tester was specifically designed to measure fluoride concentrations in various samples. Using its ion-selective measurement principle, it can detect fluoride in very small sample volumes (from 0.3 ml or 0.1 ml with sampling sheet) and covers a wide measurement range from 0.1 to 990 ppm. This makes the device versatile, suitable for applications from drinking water analysis to industrial processes. Mobile Fluoride Ion Tester for Precise Water and Environmental Analysis Equipped with a fluoride-selective electrode, the tester provides high measurement accuracy of ±2% of the reading. Automatic two-point calibration (1 ppm and 10 ppm) ensures reliable results. Additional features like Auto-Hold and Auto-Stable support accurate reading of stable values in the field. The IP67 waterproof housing protects the device from moisture and dust. A replacement sensor is also available to ensure long-term use of your Horiba LAQUAtwin Fluoride Ion Tester. Why Fluoride Measurement Is Important – Horiba Hand Tester as an Ideal Solution Fluoride content is a critical parameter in drinking water monitoring, environmental analysis, and in medical and industrial applications. Both excessively high and low fluoride concentrations can have health, ecological, or regulatory impacts, making regular monitoring essential. A mobile fluoride hand tester allows rapid on-site analysis without time-consuming laboratory testing. The robust IP67-protected design, replaceable sensor, and easy operation make the Horiba LAQUAtwin Fluoride Tester an ideal solution for routine checks, field measurements, and quality control. Applications of the Horiba Fluoride Pocket Tester Health and Dentistry: Experts use the F-11 to monitor fluoride levels in drinking water, a crucial measure to prevent dental diseases and promote oral health. Water Quality Monitoring: Environmental technicians use the tester to check fluoride concentrations in drinking water, wastewater, and natural bodies of water, ensuring compliance with environmental standards and safety regulations. Industrial Applications: To meet occupational and environmental safety standards, the F-11 allows rapid testing of process and wastewater in industries where fluoride compounds are used or produced. Environmental Analysis: The pocket tester delivers precise data for studying the effects of fluoride on biological systems, particularly where water quality monitoring and regulatory compliance are required.

Manufacturer Part No. 3200965260 LAQUAtwin ORP-11: The world's first pocket-sized ORP and Eh meter Your mobile laboratory - for use on site: Ideal for water quality tests in swimming pools, environmental tests and many other applications. HORIBA's unique compact meter integrates electrode, display and sample container to enable simple, effective on-site testing by direct measurement with a single drop.  Versatile measurement: The only pocket-sized ORP meter that can measure not only the ORP value but also the Eh value (voltage measurement versus the standard hydrogen electrode or SHE) Precision in every drop: The replaceable sensor with platinum disc enables measurements in samples as small as 0.3 ml (or 0.05 ml with sampling sheet). Wide measuring range: With a measuring range from -1000 mV to 1000 mV, the meter ensures accurate readings over a wide range. Simple automatic one-point calibration: The meter automatically recognises and calibrates the 225 mV standard solution included in the kit. The calibration can be adjusted with a different ORP standard solution. Exceptional accuracy: With an accuracy of +/- 2 mV, the meter delivers precise results every time. Auto Stable & Auto Hold measurement modes: To help users record stable readings, the meter displays a smiley face and can freeze the reading. Temperature Compensation and Calibration: The meter displays temperatures up to 50.0 °C and allows for temperature compensation and correction through its calibration function. IP67 rating: Water and dustproof meter with digital LCD display and backlighting Complete package for ORP testing on the go: Each ORP-11 meter comes with a 225 mV ORP standard solution (14 ml), a cotton swab for polishing the platinum disc, a pipette, batteries and 5 sampling sheets.

Mobile Calcium Ion Tester from Horiba with Temperature Measurement – precise, compact, robust Handheld Ca²⁺ pocket tester with 2-point calibration and temperature display – ideal for water and environmental applications The mobile Horiba LAQUAtwin calcium ion tester measures both the Ca²⁺ concentration and the temperature of a sample. Equipped with an ion-selective sensor, a digital LCD display, and a minimal sample volume of only 0.3 ml (0.05 ml when using the sampling sheet), it delivers fast and reliable measurement results. Thanks to the integrated temperature display and automatic temperature compensation, calcium values can be measured accurately even under changing environmental conditions – making the device ideal for mobile applications. Mobile calcium ion tester for precise on-site measurements With two calibration points and automatic standard recognition (150 and 2000 ppm), the device can be flexibly adapted to different measurement situations. Temperature-compensated measurement, multiplicative compensation, automatic stability and hold modes, as well as automatic shut-off ensure easy and reliable operation. The tester is dustproof and waterproof according to IP67 and offers a long battery life of approximately 400 hours. It is supplied complete with standard solutions, sampling sheets, pipette, and batteries. Why calcium measurement is important – optimal results with the Horiba handheld tester Calcium is a key parameter in water, environmental, aquaculture, and food analysis. Calcium concentration influences water hardness, biological processes, coral growth, and product quality in beverages and food. Deviations can lead to ecological, technical, or quality-related impacts. A mobile calcium handheld tester allows fast analysis directly at the point of use without complex laboratory procedures. This makes it possible to detect changes immediately and take timely action. The Horiba LAQUAtwin calcium tester combines this flexibility with high measurement accuracy, simple operation, and a robust design. Typical applications of the Horiba LAQUAtwin calcium tester Aquaculture and corals Laboratories and schools Water treatment Beverages and food

Mobile Sodium Ion Tester from Horiba with Temperature Measurement – precise and robust High-precision sodium ion tester with 2-point calibration – ideal for water and environmental analysis The Horiba LAQUAtwin Na-11 sodium ion tester was specifically designed for accurate measurement of sodium concentrations in a wide range of samples. The device enables direct on-site measurements. Its clear display shows both the Na⁺ concentration and the sample temperature in a single step, making field, laboratory, and greenhouse work significantly more efficient. Mobile sodium ion tester for precise on-site measurements Featuring 2-point calibration and automatic standard recognition (150 and 2000 ppm), the instrument can be easily adapted to different measurement requirements. The integrated temperature display and automatic temperature compensation ensure accurate results even under fluctuating environmental conditions. The robust IP67 housing is dustproof and waterproof, making the tester suitable for demanding daily use. With a battery life of approximately 400 hours, reliable long-term operation is ensured. The tester is supplied with standard solutions, sampling sheets, batteries, and matching pipettes for immediate use. Why sodium measurement matters – and why a handheld tester is the ideal solution Measuring sodium ions plays a crucial role in water, environmental, food, and agricultural analysis. Excessively high or low sodium concentrations can significantly affect water quality, soil structure, plant growth, and the quality of food products and drinking water. Regulatory limits and quality standards further require regular monitoring. A mobile sodium ion handheld tester enables fast and precise analysis directly at the point of use, without time-consuming sampling or laboratory analysis. The Horiba LAQUAtwin Na-11 combines this flexibility with high measurement accuracy and ease of use, making it ideal for routine monitoring, quality control, and research applications. Typical applications for the Horiba sodium ion tester Environmental monitoring: Measurement of sodium concentrations in surface and groundwater to assess water quality and ensure compliance with environmental standards. Food and beverage production: Testing sodium levels in food and beverages for quality assurance, product development, and regulatory compliance. Agriculture: Monitoring sodium content in irrigation water and soils to support plant health and optimize water management. Research & development: Use in laboratories for experimental studies on sodium ion behavior under varying conditions. Education: Utilized in schools and universities to demonstrate the use of ion-selective electrodes in analytical chemistry.