The HORIBA LAQUAtwin Pocket Tester series provides a comprehensive solution for fast and precise measurement of water quality parameters directly in the field. To ensure these measurements remain reliable and accurate, regular monitoring of the sensors and, if necessary, replacement with spare sensors is crucial. These replacement sensors are tailor-made for the HORIBA LAQUAtwin series and cover a wide range of types for various measurements: pH, conductivity, salinity, redox (ORP), as well as ion-selective sensors for sodium, potassium, nitrate, calcium, and fluoride. Each sensor is designed to maximize user-friendliness and accuracy, which HORIBA is renowned for in water quality testing worldwide. HORIBA replacement sensors guarantee users that their devices consistently deliver optimal performance and precise measurements. Advantages of HORIBA Replacement Sensors: Easy Replacement: Sensors can be exchanged quickly, allowing uninterrupted measurement. High Accuracy: Replacement sensors ensure precise and reliable results. Wide Measurement Range: Various sensor types are available to capture a broad spectrum of water quality parameters. Durability: Sensors are designed for long service life, even under challenging conditions. Sensor Replacement Instructions: Follow these steps to replace the sensor and maintain the longevity and accuracy of your HORIBA LAQUAtwin Pocket Tester: Removing the Sensor: Turn off the tester. Lift the sensor tip slightly and pull the sensor away from the device. Completely detach the sensor from the tester. Installing the Sensor: Make sure the tester is turned off. Ensure the waterproof gasket is intact and clean. Attach the sensor to the tester so that hook “A” on the back of the device fits into hole “a” on the sensor tip. Make sure the waterproof gasket is not twisted. Important: After replacing the sensor, follow the instructions in the user manual of the respective tester to make the device ready for accurate measurements. This typically includes calibration and, if necessary, conditioning. How can I tell if my sensor is worn out? Check the sensor condition as follows: Perform a 2-point calibration. If an error occurs during calibration, this indicates that the sensor has deteriorated. In this case, the sensor should be replaced. Regular checks and timely replacement of sensors ensure the high quality and reliability of your water quality measurements with HORIBA LAQUAtwin Pocket Testers. Manufacturer Part Nr. 3200459866

The HORIBA LAQUAtwin Pocket Testers provide a comprehensive solution for immediate and precise measurement of water quality parameters directly in the field. To ensure that these measurements remain reliable and accurate, it is important to regularly check the sensors and replace them with spare sensors if necessary. The replacement sensors developed for the HORIBA LAQUAtwin series cover various types for different measurements: pH, conductivity, salinity, redox (ORP), as well as ion-selective sensors for sodium, potassium, nitrate, calcium, and fluoride. All of these sensors are designed to maximize user-friendliness and precision, qualities for which HORIBA is globally recognized in water quality testing. HORIBA replacement sensors ensure that users’ devices consistently deliver optimal performance and accurate measurements. Advantages of HORIBA Replacement Sensors: Easy Replacement: Sensors can be quickly exchanged, allowing measurements to continue without delay. High Precision: Replacement sensors ensure that results are exact and reliable. Wide Measurement Range: Various sensor types are available to capture a broad spectrum of water quality parameters. Durability: Sensors are designed for long service life, even under challenging conditions. Sensor Replacement Instructions: To ensure the longevity and accuracy of your HORIBA LAQUAtwin Pocket Tester, please follow these instructions when replacing a sensor: Removing the Sensor: Turn off the tester. Carefully detach the sensor from the device and lift the sensor tip. Completely separate the sensor from the tester so that the two components are no longer connected. Installing the Sensor: Ensure the tester is turned off. Check that the waterproof gasket is clean and undamaged. Attach the sensor to the tester by inserting hook “A” on the back of the device into hole “a” on the sensor tip. Make sure the waterproof gasket is not twisted. Important: After replacing the sensor, it is essential to follow the steps in the user manual of the respective tester to make the device ready for accurate measurements. (These manuals are available with the products. Calibration and, if necessary, conditioning are usually required.) How can I check if my sensor shows signs of wear? Check the sensor condition as follows: Perform a 2-point calibration. If an error occurs during calibration, this indicates that the sensor has deteriorated. In this case, replacing the sensor is recommended. Regular checks and timely replacement of sensors are essential to ensure the high standards and reliability of water quality measurements performed with HORIBA LAQUAtwin Pocket Testers. Manufacturer Part Nr. 3200597237