HORIBA Ion standard solutions, ionic strength controllers and ion-selective electrode filling solutions are indispensable for accurate and reproducible measurements with ion-selective electrodes (ISE). A large number of analyses in laboratories and in the field, such as testing water and wastewater quality, environmental monitoring and quality control in industrial processes, rely on these solutions. Ionic standard solutions are used to calibrate ion-selective electrodes and ensure precise measurement. Horiba's standard solutions have a known ion concentration. They are therefore essential for setting up the electrodes correctly before using them for test runs. Ionic strength controllers are specifically designed to adjust the ionic strength of the sample to enable accurate measurements. They are particularly important when the composition of the samples could affect the measurement or in samples with low ionic strength. The ionic strength can be adjusted to stabilize the ionic activity in the solution. This leads to more accurate measurement results. Ion-selective electrode filling solutionsIon-selective electrode filling solutions are specific solutions that are filled into ion-selective electrodes. They ensure the proper operation of the electrode and help to maintain the potential required to measure the specific ion. To ensure that measurements meet international standards and to ensure conformity with regulatory and compliance standards, these specialized solutions are essential. Many industries, from pharmaceutical to environmental, use these solutions to meet their quality and safety requirements. For users working in areas such as water analysis, environmental monitoring or regulatory testing environments, these solutions ensure the accuracy and reliability required for critical measurements. To provide reliable data for important environmental, health and safety decisions, they are a crucial part of analytical chemistry. Overall, HORIBA's solutions enable experts to make the best use of their instruments and achieve the precise results required for their applications. Manufacturer article number: 3200697169 (500-CL-ISA)

HORIBA Ion standard solutions, ionic strength controllers and ion-selective electrode filling solutions are indispensable for accurate and reproducible measurements with ion-selective electrodes (ISE). A large number of analyses in laboratories and in the field, such as testing water and wastewater quality, environmental monitoring and quality control in industrial processes, rely on these solutions. Ionic standard solutions are used to calibrate ion-selective electrodes and ensure precise measurement. Horiba's standard solutions have a known ion concentration. They are therefore essential for setting up the electrodes correctly before using them for test runs. Ionic strength controllers are specifically designed to adjust the ionic strength of the sample to enable accurate measurements. They are particularly important when the composition of the samples could affect the measurement or in samples with low ionic strength. The ionic strength can be adjusted to stabilize the ionic activity in the solution. This leads to more accurate measurement results. Ion-selective electrode filling solutionsIon-selective electrode filling solutions are specific solutions that are filled into ion-selective electrodes. They ensure the proper operation of the electrode and help to maintain the potential required to measure the specific ion. To ensure that measurements meet international standards and to ensure conformity with regulatory and compliance standards, these specialized solutions are essential. Many industries, from pharmaceutical to environmental, use these solutions to meet their quality and safety requirements. For users working in areas such as water analysis, environmental monitoring or regulatory testing environments, these solutions ensure the accuracy and reliability required for critical measurements. To provide reliable data for important environmental, health and safety decisions, they are a crucial part of analytical chemistry. Overall, HORIBA's solutions enable experts to make the best use of their instruments and achieve the precise results required for their applications. Manufacturer article number: 3200697178 (500-CL-ISA)

The High-End LAQUA F-72 forms the top of the laboratory instruments series and measures the parameters pH, ORP, ion, as well as temperature. Ion selective parameters (each with his own electrode):  Ammonia ion (NH3), Calcium ion (Ca2+), Chloride ion (Cl-), Fluoride ion (F-), Nitrate Ion (NO3-), Potassium ion (K+) The auto-diagnostic function of the F- series allows the user to ensure that the instruments always provide powerful and reliable measurements. The LAQUA F-72 is fully GLP/GMP compliant and can be connected to an external printer. To ensure traceability, all results are recorded along with sample name, user ID and calibration information. The instrument offers you the proven calibration functions with automatic buffer recognition, stability display as well as the display of the electrode status (wear indicator). We offer a comprehensive range of conductivity electrodes suitable for all types of applications and samples. Known for their stability and durability, HORIBA's electrodes provide accurate measurements under all conditions.LAQUA's large capacitive touch screen panel:Large 5,7" (115,2 x 86,4 mm) graphic touch- color screen Display easy-to-understand menus for values and functionsEffortless single-touch operations- tap, flick and dragSwitch between real-time digital graphs or analogue displays during measurement with a single finger movement  Single channel displayExtensive on-screen support on the meter through an electronic user manual with colour images that can be accessed at any time and includes problem-solving instructions for calibration or measurementFeatures:Easy navigation for main instrument and electrode inspections Mode for periodic inspections: JIS/pharmacopoeia/digital simulator Customisable auto-hold function for calibration and measurement Simultaneous connection to a GLP/GMP compliant and a PC Digital memory - up to 2,000 measurement data sets can be recorded360° electrode stand which holds up to three electrodes and is height adjustable  USB PC communication and USB memory  Multilingual support (Japanese, English, Chinese, Korean)Scope of deliveryF-72 Meterelectrode standprotection coverpower adaptor with 6 plugsdata acquisition software in USB9615S-10D - refillable, glass-body pH electrode with integrated temperature sensor, 1m cable, BNC & phono jack502-S - each 1x pH 4.01, 7.00, 10.01, 3.33M KCl solution (250 ml)

The Dual Channel LAQUA F-73 forms the top of the laboratory instruments series and measures the parameters pH, ORP, ion, as well as temperature.  Ion selective parameters (each with his own electrode):  Ammonia ion (NH3), Calcium ion (Ca2+), Chloride ion (Cl-), Fluoride ion (F-), Nitrate Ion (NO3-), Potassium ion (K+) The auto-diagnostic function of the F- series allows the user to ensure that the instruments always provide powerful and reliable measurements. The LAQUA F-73 is fully GLP/GMP compliant and can be connected to an external printer. To ensure traceability, all results are recorded along with sample name, user ID and calibration information. The instrument offers you the proven calibration functions with automatic buffer recognition, stability display as well as the display of the electrode status (wear indicator). We offer a comprehensive range of conductivity electrodes suitable for all types of applications and samples. Known for their stability and durability, HORIBA's electrodes provide accurate measurements under all conditions.LAQUA's large capacitive touch screen panel:Large 5,7" (115,2 x 86,4 mm) graphic touch- color screen Display easy-to-understand menus for values and functionsEffortless single-touch operations- tap, flick and dragSwitch between real-time digital graphs or analogue displays during measurement with a single finger movement  Switchable single or dual channel displayExtensive on-screen support on the meter through an electronic user manual with colour images that can be accessed at any time and includes problem-solving instructions for calibration or measurementFeatures:Easy navigation for main instrument and electrode inspections Mode for periodic inspections: JIS/pharmacopoeia/digital simulator Customisable auto-hold function for calibration and measurement Simultaneous connection to a GLP/GMP compliant and a PC Digital memory - up to 2,000 measurement data sets can be recorded360° electrode stand which holds up to three electrodes and is height adjustable  USB PC communication and USB memory  Multilingual support (Japanese, English, Chinese, Korean)Scope of deliveryF-73 Meterelectrode standprotection coverpower adaptor with 6 plugsdata acquisition software in USB Manufacturer article number: 3200575123 (F-73G)

Multifunctional Dual-Channel Laboratory Meter for pH, Redox, Ion-Selective Parameters, and More Professional Horiba F-74 Laboratory Device for Simultaneous Analysis of Multiple Water and Ion Parameters The Horiba F-74 dual-channel laboratory device combines a wide range of analytical measurement methods for various parameters in a powerful system. It measures pH, redox, temperature, conductivity, resistance, salinity, TDS, and ion-selective parameters. The device operates with two independent channels: The first channel is designed for measuring pH, ion-selective parameters, mV, and redox potential. The second channel can measure conductivity, salinity, resistance, and TDS. Automatic buffer and calibration solutions, visual stability indicators, and integrated electrode status ensure reliable and repeatable results. This channel separation allows different parameters to be measured efficiently and simultaneously, supporting safe and convenient operation in the laboratory. Powerful Dual-Channel System for Precise Laboratory Analysis The Horiba F-74 is designed for laboratory environments where measurement accuracy, documentation, and process safety are crucial. Simultaneous recording of multiple parameters saves time and increases the analytical value, especially for complex samples. Its intuitive operation makes the device suitable for both routine analyses and demanding measurement tasks in research, quality control, and industry. Technical Highlights and Key Advantages of the Horiba F-74 Dual-Channel Laboratory Device The laboratory meter offers numerous features that simplify daily use and support compliance with standards: Touchscreen color display for intuitive control and clear visualization Automatic buffer and calibration recognition for reliable results GLP/GMP compliance for regulated applications Data storage and PC communication for easy archiving and analysis The combination of measurement versatility, user-friendliness, and high precision makes the Horiba F-74 an ideal solution for professional multi-parameter laboratory analyses. Frequently asked questions How long is the warranty period for HORIBA analysers? The warranty period is 2 years for the 300 (WQ) series and 1 year for the F series after delivery. Where can I find suitable replacement electrodes or buffer solutions? You can find the appropriate replacement electrodes and buffer solutions in the shop under the main item at the bottom of the cross-selling section. How do I clean the probe before calibration? The sensors should be cleaned with DI water (deionised). After cleaning, wipe them with tissue paper if possible.

High-end laboratory measuring instrument for analytics  Dear customers, herewith we offer you our highly professional Horiba laboratory table-top measuring instrument of the 2000 series.  The LAQUA 2000 series laboratory tabletop meter has a very high-quality 5 inch display with backlighting which shows you all the important information, such as the measured value with up to four decimal places in this version (depending on the resolution), the temperature, the date with time and much more.  The LAQUA 2000 series also offers you an adequate device memory with automatic data storage after a set time interval to document your daily measurements accurately over a long period of time. To protect the device settings from unauthorised access, they are password-protected. After your measurements, you can easily transfer all measurement data from the device to your PC via a USB cable in CSV, Excel and Pdf formats using the DAS20 software.  In order to facilitate your daily work with the device, the table measuring device visualises the correct calibration, the stable measurement as well as the electrode wear condition. The operation is intuitive because the available keys are marked with symbols and abbreviations. After the analysis, you can clean the device easily and in a time-saving manner with a damp cloth, as the surface is dirt-repellent due to its nature. With the electrode stand included in the scope of delivery, two electrodes can be held and adjusted in height. This allows you to individually align your electrode to your container or glass for calibration and measurement. Special features of the Laqua ION2000 model : The ION2000 is a laboratory meter to which you can connect the separately available ion-selective Horiba probes or determine the pH value and the redox value via the electrodes. Single input, connection of one electrode. Ions (ammonia, calcium, chloride, fluoride, nitrate, potassium)  Measurement ion-selective  accepts combined and half-cell ion-selective electrodes  wide measuring range from 0.000 μg/L to 9999 g/L  accepts up to 5 user-defined ion calibration points  choice of preferred units: μg/L - mg/L - g/L, ppm - ppt, mmol/L - mol/L  Resolution of 4 significant digits after the decimal point with automatic scaling  pH-ORP wide measuring range; -2.000 to 20.000 pH  high accuracy; ± 0.003 pH  resolution: 0.1, 0.01 or 0.001 pH  continuous display of calibrated points  display of offset and slope - by segment and average up to 5 pH  calibration points ± 2000.0 mV  1-point redox calibration  automatically recognises and calibrates USA, NIST, NIST2 and DIN pH buffers  allows CUST (Custom) buffers for manual calibration  Below we would like to show you in full the general functions of the Horiba LAQUA 2000 series:  internal memory for up to 2000 data sets, measurement data with time and date information  records and stores data in the unit memory based on a specified time interval  a 4-digit password protects the meter set-up mode from unauthorised access  data can be transferred to a computer and exported in the following formats CSV/Excel/PDF  GLP/GMP compliance of the instrument as data can be displayed, recorded and printed with date and time stamp on the instrument  Software updates can be downloaded to the instrument  Calibration reminder function, indicates that it is time to calibrate (alarm adjustable up to 90 days)  Electrode holder is mounted on the meter and can hold up to 2 electrodes (rotates 360º and can be moved up and down 30cm)  Displays measurement stability in measurement and calibration mode  displays electrode condition based on calibration data  smooth surface, easy cleaning  RS-232/USB, therefore easy PC and printer connection and free instrument software  Ergonomic design for easy viewing and operation  Clearly labelled and easy-to-use ports for communication and measurement  5" digital display with backlight, shows all important measurement values and status  Automatic calibration, recognises a wide range of standard solutions adjustable switch-off time (up to 30 minutes)  temperature compensation, the temperature in °C or °F is either automatically detected if a temperature sensor is connected (ATC mode) or manually entered by the user  several measuring modes:  Auto-Stable mode signals a stable measured value, Auto-Hold mode holds a stable measured value Real Time mode continuously displays current readings  small meter footprint of 155 x 150 mm, saves valuable space  Temperature detection, easy display of sample temperature user selectable resolution, up to 3 digits  Fixed and individual calibration points Easy navigation, navigate through the settings menu by up, down, right and left  Scope of delivery:  Measuring device with integrated electrode stand  Universal mains adapter with 6 plugs  Operating instructions  Manufacturer part number: Meter only ION2000 (3200896963) 

High-end laboratory measuring instrument for analytics  Dear customers, herewith we offer you our highly professional Horiba laboratory table-top measuring instrument of the 2000 series.  The LAQUA 2000 series laboratory tabletop meter has a very high-quality 5 inch display with backlighting which shows you all the important information, such as the measured value with up to three decimal places (depending on the resolution), the temperature, the date with time and much more.  The LAQUA 2000 series also offers you an adequate device memory with automatic data storage after a set time interval to document your daily measurements accurately over a long period of time. To protect the device settings from unauthorised access, they are password-protected. After your measurements, you can easily transfer all measurement data from the device to your PC via a USB cable in CSV, Excel and Pdf formats using the DAS20 software.  In order to facilitate your daily work with the device, the table measuring device visualises the correct calibration, the stable measurement as well as the electrode wear condition. The operation is intuitive because the available keys are marked with symbols and abbreviations. After the analysis, you can clean the device easily and in a time-saving manner with a damp cloth, as the surface is dirt-repellent due to its nature. The electrode stand included in the starter set can be used to hold two electrodes and adjust their height. This allows you to individually align your electrode to your container or glass for calibration and measurement. Special features of the Laqua PC2000 model (multi-parameter): The PC2000 is a combination of the ION2000 and the EC2000 with the advantage that you can measure all parameters with one device. Dual input, connection of 2 electrodes at the same time. pH-ORP wide measuring range; -2.000 to 20.000 pH  high accuracy; ± 0.003 pH  resolution: 0.1, 0.01 or 0.001 pH  continuous display of calibrated points  display of offset and slope - by segment and average up to 5 pH  calibration points ± 2000.0 mV  1-point redox calibration  automatically recognises and calibrates USA, NIST, NIST2 and DIN pH buffers  allows CUST (Custom) buffers for manual calibration  Conductivity-resistivity-TDS-salinity wide measuring range from 0.001μS/cm to 2,000 S/cm  allows automatic and manual conductivity calibrations  records individual and average calibration factors after conductivity calibration  Calculates resistance, TDS and salinity based on measured conductivity  7 conductivity ranges:   0.000 to 1.999 μS/cm (k = 0.1)  2.00 to 19.99 μS/cm (k = 0.1, 1)  20.0 to 199.9 μS/cm (k = 0.1, 1, 10)  200 to 1999 μS/cm (k = 0.1, 1, 10)  2.00 to 19.99 mS/cm (k = 0.1, 1, 10)  20.0 to 199.9 mS/cm (k = 1, 10)  0.200 to 2.000 S/cm (k = 10) Ions (ammonia, calcium, chloride, fluoride, nitrate, potassium)  Measurement ion-selective accepts combined and half-cell ion-selective electrodes wide measuring range from 0.000 μg/L to 9999 g/L accepts up to 5 user-defined ion calibration points choice of preferred units: μg/L - mg/L - g/L, ppm - ppt, mmol/L - mol/L Resolution of 4 significant digits after the decimal point with automatic scaling  Below we would like to show you in full the general functions of the Horiba LAQUA 2000 series: internal memory for up to 2000 data sets, measurement data with time and date information records and stores data in the unit memory based on a specified time interval a 4-digit password protects the meter set-up mode from unauthorised access data can be transferred to a computer and exported in the following formats CSV/Excel/PDF GLP/GMP  compliance of the instrument as data can be displayed, recorded and printed with date and time stamp on the instrument Software updates can be downloaded to the instrument Calibration reminder function, indicates that it is time to calibrate (alarm adjustable up to 90 days) Electrode holder is mounted on the meter and can hold up to 2 electrodes (rotates 360º and can be moved up and down 30cm). Electrode holder only included in the starter set.Displays measurement stability in measurement and calibration mode displays electrode condition based on calibration data smooth surface, easy cleaning RS-232/USB, therefore easy PC and printer connection and free instrument software Ergonomic design for easy viewing and operation Clearly labelled and easy-to-use ports for communication and measurement 5" digital display with backlight, shows all important measurement values and status Automatic calibration, recognises a wide range of standard solutionsadjustable switch-off time (up to 30 minutes) temperature compensation, the temperature in °C or °F is either automatically detected if a temperature sensor is connected (ATC mode) or manually entered by the user several measuring modes: Auto-Stable mode signals a stable measured value,Auto-Hold mode holds a stable measured valueReal Time mode continuously displays current readings small meter footprint of 155 x 150 mm, saves valuable space Temperature detection, easy display of sample temperature user selectable resolution, up to 3 digits Fixed and individual calibration pointsEasy navigation, navigate through the settings menu by up, down, right and left Scope of delivery: Measuring device with integrated electrode stand Universal mains adapter with 6 plugs Operating instructions Starter set version additionally contains 9625-10D refillable pH electrode with plastic body 9382-10D conductivity electrode with plastic body, cell constant k=1.0 pH 4, 7 and 10 buffer solutions & 3.33M KCl (1 x 250ml each) 84 µS/cm, 1413 µS/cm, 12.88 mS/cm (1 x 250ml each) with electrode holderFlow cell available in combination with 9371-10 stainless steel conductivity cell for ultrapure water measurement (300-2C-C) Manufacturer part number:Meter only   PC2000 (3200896964) Starter-set   PC2000-SR (1300098882)

Thank you for your interest in our smart and individually configurable measuring instruments of the HORIBA LAQUA WQ-300 series. The high-quality digital multi-parameter handheld meters feature a large colour LCD display with LED backlight (7 cm x 5.2 cm), making them ideally suited for field use under a wide range of conditions and in direct daylight. Use our configurator to select the appropriate measuring instrument from the HORIBA WQ-300 series with 1 to 3 measuring channels, the desired measuring parameters (sensor cartridges) and the required cable length according to your individual needs. The sensor cables feature an integrated sensor receptacle and digital module. Additional measuring parameters can also be connected at a later stage using the corresponding sensor cable or carried in the measuring case as supplementary equipment. As with other HORIBA handheld meters, the devices are particularly resistant to shocks, slipping and scratches thanks to their special rubber coating. Operation requires four standard AA batteries with 2500 mAh. For greater flexibility during mobile use, the WQ-300 series can alternatively be powered by a power bank or battery pack via the integrated USB interface. An IP67 certification, which confirms dust-tightness and protection against temporary immersion for up to 30 minutes at a water depth of one metre, completes the professional overall package alongside the ergonomic design and easy operation. HORIBA offers a three-year warranty on the handheld measuring instruments of the LAQUA WQ-300 series. Functions and Features During measurements, users are supported by operating instructions displayed in the form of smiley symbols. These are complemented by an LED status indicator on the sensor to help prevent operating errors and implausible measurement results. The small number of control buttons and the absence of complex, nested menus ensure that the instruments remain easy and safe to operate, even when used intermittently or by different users. Additional Functions Electrode wear indicator Measurement stability indicator on the instrument and sensor Hold function to "save" the current measured value on the display Individual measuring point identification with up to 8 characters Automatic calibration functions Integrated sensor holders Self-diagnostic function GLP functions Fold-out stand for convenient hands-free measurements Transfer of measurement data to a computer or smartphone via USB or WiFi Measuring Case for Mobile Use All handheld meters of the WQ-300 series are supplied in a reinforced measuring case for mobile outdoor use. The case provides space for the measuring instrument, electrodes and cables, as well as up to eight 60 ml bottles of buffer solutions. An integrated holder for buffer solution bottles facilitates calibration. Automatic Sensor Recognition A particular advantage of the WQ-300 series is automatic sensor recognition through sensor cables with integrated digital sensor receptacles. Information about the sensor, calibration data and measurement settings is stored in the digital sensor module and transmitted to the measuring instrument. In addition, all connected sensors can be calibrated simultaneously, as each sensor module independently stores measurement and calibration data and transmits them to the WQ-300 series measuring instrument. Analogue sensors can optionally be connected using the HORIBA BNC sensor adapter. Please contact us for further information. Available Languages German English French Spanish Portuguese Chinese Scope of Delivery WQ-300 series handheld meter in a carrying case Selected digital electrode, if applicable, and the corresponding sensor-specific cable with integrated digital sensor receptacle Instruction manual Manufacturer Article Number WQ-310-K (1 channel): 3200832605 Calibrating the Instrument pH Measurement To obtain accurate results, a two-point calibration must be carried out. The following buffer solutions are recommended: pH 7.00 and 4.01 for acidic samples pH 7.00 and 10.01 for alkaline samples If the expected pH value of the sample is unknown, a three-point calibration using pH 7.00, 4.01 and 10.01 is recommended. It is recommended to begin calibration with pH 7.00. Conductivity Measurement For conductivity measurements, a single-point calibration is sufficient, for example at 1413 µS/cm. For greater accuracy, a multi-point calibration can also be performed. Important Note on the Chloride Sensor Note: If a chloride sensor is selected, it is supplied without chloride ionic strength adjuster and chloride electrode filling solution. These solutions must be purchased separately by the customer. The chloride sensor cannot be used without the required filling solution. Why We Use These Measuring Devices in Water Treatment Precise calcium control is an important element of efficient water treatment, from drinking water purification and process water management to environmental analysis. Elevated calcium concentrations can contribute to scale formation, pipe damage, increased energy consumption and disruptions in chemical processes. For these applications, we offer configurable solutions from the HORIBA LAQUA WQ series in our online shop. Available Measuring Instruments WQ310-K: Single-channel solution for targeted measurements. WQ320-K: Simultaneous measurement of two parameters, such as calcium and conductivity. WQ330-K: Three-channel measurement for complex multi-parameter analyses. Benefits for Water Treatment Reliable measurement data for monitoring and optimising water treatment systems. Digital evaluation, documented measurement results and interfaces for data transfer. Robust design and practical measuring case for mobile on-site use. Flexible combination of calcium measurements with other parameters such as pH, conductivity or redox potential. Note on Scope of Delivery: From November 2026, HORIBA products will be supplied without batteries. Existing stock may still include batteries. Batteries are no longer included with newly manufactured products and must be purchased separately if required.

Thank you for your interest in our smart and individually configurable measuring instruments of the HORIBA LAQUA WQ-300 series. The high-quality digital multi-parameter handheld meters feature a large colour LCD display with LED backlight (7 cm x 5.2 cm), making them ideally suited for field use under a wide range of conditions and in direct daylight. Use our configurator to select the appropriate measuring instrument from the HORIBA WQ-300 series with 1 to 3 measuring channels, the desired measuring parameters (sensor cartridges) and the required cable length according to your individual needs. The sensor cables feature an integrated sensor receptacle and digital module. Additional measuring parameters can also be connected at a later stage using the corresponding sensor cable or carried in the measuring case as supplementary equipment. As with other HORIBA handheld meters, the devices are particularly resistant to shocks, slipping and scratches thanks to their special rubber coating. Operation requires four standard AA batteries with 2500 mAh. For greater flexibility during mobile use, the WQ-300 series can alternatively be powered by a power bank or battery pack via the integrated USB interface. An IP67 certification, which confirms dust-tightness and protection against temporary immersion for up to 30 minutes at a water depth of one metre, completes the professional overall package alongside the ergonomic design and easy operation. HORIBA offers a three-year warranty on the handheld measuring instruments of the LAQUA WQ-300 series. Functions and Features During measurements, users are supported by operating instructions displayed in the form of smiley symbols. These are complemented by an LED status indicator on the sensor to help prevent operating errors and implausible measurement results. The small number of control buttons and the absence of complex, nested menus ensure that the instruments remain easy and safe to operate, even when used intermittently or by different users. Additional Functions Electrode wear indicator Measurement stability indicator on the instrument and sensor Hold function to "save" the current measured value on the display Individual measuring point identification with up to 8 characters Automatic calibration functions Integrated sensor holders Self-diagnostic function GLP functions Fold-out stand for convenient hands-free measurements Transfer of measurement data to a computer or smartphone via USB or WiFi Measuring Case for Mobile Use All handheld meters of the WQ-300 series are supplied in a reinforced measuring case for mobile outdoor use. The case provides space for the measuring instrument, electrodes and cables, as well as up to eight 60 ml bottles of buffer solutions. An integrated holder for buffer solution bottles facilitates calibration. Automatic Sensor Recognition A particular advantage of the WQ-300 series is automatic sensor recognition through sensor cables with integrated digital sensor receptacles. Information about the sensor, calibration data and measurement settings is stored in the digital sensor module and transmitted to the measuring instrument. In addition, all connected sensors can be calibrated simultaneously, as each sensor module independently stores measurement and calibration data and transmits them to the WQ-300 series measuring instrument. Analogue sensors can optionally be connected using the HORIBA BNC sensor adapter. Please contact us for further information. Available Languages German English French Spanish Portuguese Chinese Scope of Delivery WQ-300 series handheld meter in a carrying case Selected digital electrode, if applicable, and the corresponding sensor-specific cable with integrated digital sensor receptacle Instruction manual Manufacturer Article Number WQ-320-K (2 channels): 3200832606 Calibrating the Instrument pH Measurement To obtain accurate results, a two-point calibration must be carried out. The following buffer solutions are recommended: pH 7.00 and 4.01 for acidic samples pH 7.00 and 10.01 for alkaline samples If the expected pH value of the sample is unknown, a three-point calibration using pH 7.00, 4.01 and 10.01 is recommended. It is recommended to begin calibration with pH 7.00. Conductivity Measurement For conductivity measurements, a single-point calibration is sufficient, for example at 1413 µS/cm. For greater accuracy, a multi-point calibration can also be performed. Important Note on the Chloride Sensor Note: If a chloride sensor is selected, it is supplied without chloride ionic strength adjuster and chloride electrode filling solution. These solutions must be purchased separately by the customer. The chloride sensor cannot be used without the required filling solution. Note on Scope of Delivery: From November 2026, HORIBA products will be supplied without batteries. Existing stock may still include batteries. Batteries are no longer included with newly manufactured products and must be purchased separately if required.

Horiba WQ330-K – Your Professional 3-Channel Water Quality Meter Expandable multi-parameter system for simultaneous measurement of pH, conductivity, redox, and other water parameters The Horiba LAQUA WQ330-K is a powerful multi-channel device for advanced water analysis, both on-site and in the laboratory. With three freely configurable measurement channels, it can simultaneously record parameters such as pH, conductivity, redox potential, TDS, temperature, oxygen, ammonia, calcium, chloride, nitrate, fluoride, and potassium. Intuitive operation, automatic sensor recognition, and digital calibration ensure accurate, fast, and reproducible measurements. Flexible Multi-Parameter System for Field and Laboratory Applications The analysis kit with the Horiba WQ330-K is ideal for environmental and water body monitoring, research and teaching, as well as drinking and process water control. The large LCD display with LED backlight ensures excellent readability even in direct sunlight. Measurement data can be exported and documented via USB or wirelessly, greatly simplifying traceability and analysis. The modular system allows the device to be quickly and precisely adapted to any measurement task. It is ideal for users who need to efficiently and reliably monitor multiple water parameters. Technical Features and Key Advantages of the WQ330-K The three measurement channels of the Horiba WQ330-K enable simultaneous recording of different water parameters, reducing measurement time and allowing better evaluation of relationships between parameters. The modular sensor concept allows flexible use of digital sensors, which are automatically recognized and store their calibration history. Notably, the combination of high measurement precision, user-friendliness, and mobility makes this device stand out. Quick deployment without complicated setup, along with easy data transfer for documentation and analysis, makes the Horiba LAQUA WQ330-K an ideal solution for professional water analytics. Calibrating the instrument: pH measurement To obtain accurate results, a two-point calibration must be carried out. It is recommended that the following solutions be used: pH 7.00 and 4.01 for acidic samples pH 7.00 and 10.01 for alkaline samples Carry out a three-point calibration using pH 7.00, 4.01 and 10.01 if you do not know the expected pH value of the sample. It is recommended that you calibrate using pH 7.00 first. Conductivity measurement For a conductivity measurement, a single-point calibration is sufficient, for example at 1413 μS/cm. For greater accuracy, a multi-point calibration can also be carried out. Note: During the promotional period, the discount on accessories will be automatically deducted at the shop’s checkout when purchased together with the HORIBA WQ330 device. Note on Scope of Delivery: From November 2026, HORIBA products will be supplied without batteries. Existing stock may still include batteries. Batteries are no longer included with newly manufactured products and must be purchased separately if required. Frequently asked questions How long is the warranty period for HORIBA analysers? The warranty period is 2 years for the 300 (WQ) series and 1 year for the F series after delivery. Where can I find suitable replacement electrodes or buffer solutions? You can find the appropriate replacement electrodes and buffer solutions in the shop under the main item at the bottom of the cross-selling section. How do I clean the probe before calibration? The sensors should be cleaned with DI water (deionised). After cleaning, wipe them with tissue paper if possible. Frequently asked questions about the promotion How long does the promotion run for? The promotion runs from 1 September 2026 to 31 December 2026. How do I get the discount on the accessories? The discount will be automatically deducted at the shop’s checkout when you purchase the HORIBA WQ330 unit at the same time.